TO START: 1. Remove and inventory JBA exhaust 2. Disconnect negative battery cable and allow vehicle exhaust to cool. 3. With the vehicle raised and properly supported, using the 15mm socket and ratchet, loosen the clamp, at the rear of the muffler, that secures the tail pipe to the muffler. 4. Spray lubricant on the exhaust pipe behind the muffler. 5. Spray lubricant on all factory rubber isolators. 6. Remove the factory tail pipe hanger from rubber isolator. 7. Remove tail pipe from the rea... Read Full Story

Step 1: Prior to lifting the vehicle it is recommended that you measure the stock height so that you have a base line measurement. Measure from the bottom of the wheel to the lip of the fender, as in Insert A. Position truck on a flat surface and lift vehicle by the frame so that the front wheels are off the ground. Use a floor jack and jack stands or a (2) two post lift if available. Step 2: Remove the upper sway bar end link hardware, the lower strut mount hardware, the three (3) nuts on th... Read Full Story

TO START: 1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable. 2. Disconnect the air temp. sensor electrical connection. 3. Loosen the hose clamps at the turbo inlet and the airbox outlet as shown. 4. Remove the intake tube from the vehicle as shown. 5. Loosen and remove the 10mm nut that retains the airbox to the vehicle. 6. Remove the complete airbox assembly. (more…) Read Full Story

Prior to installation, carefully inspect the vehicle’s steering and drive train components. Be sure to check ball joints, tie rod ends, pan-rod bar, and control arm bushings. Everything must be tight and in good working condition. • We recommend installation be done by a trained professional • Read instructions carefully before attempting installation • Secure and properly block vehicle prior to installation • Front end alignment is necessary upon completion of install. (more…) Read Full Story

Remove air cleaner assembly. a) Disconnect air tube from air box. b) Remove air box lid and filter. c) Remove air cleaner assembly from fender. Loosen nut at rear near washer reservoir. Remove plastic stud from filter box snout, then remove assembly from vehicle. (more…) Read Full Story

Get ready to install the kit. 1. Remove the shift transfer case shift linkage. a. If present on your vehicle, remove four bolts and skid plate from the frame under the transmission and transfer case. b. Remove two rubber bushings and transfer case shift linkage from shift lever and transfer case. 2. Remove the front bumper. a. Remove nine panel clips, plastic cover, and rubber cover from the core support. b. If present on your vehicle, disconnect two wire harness connectors from the driving l... Read Full Story

Proper installation of this kit requires knowledge of the factory recommended procedures for removal and installation of original equipment components. We recommend that the factory shop manual and any special tools needed to service your vehicle be on hand during the installation. Installation of this kit without proper knowledge of the factory recommended procedures may affect the performance of these components and the safety of the vehicle. We strongly recommend that a certified mechanic ... Read Full Story

PowerAid Throttle Body Spacer Installation Instructions for 03-08 Dodge Ram 5.7L Hemi 1. DISCONNECT NEGATIVE (-) BATTERY CABLE. 2. Loosen the hose clamp and remove the air tube from the throttle body air box. 3. Disconnect the air temperature sensor connector attached to the air box. 4. Loosen the two bolts that secure the air box using a 10mm socket. 5. Remove the oil filler cap (for clearance if needed) and carefully pull and remove the air box. * Be careful not to drop anything in the oil ... Read Full Story

STEP 1. Open up the power outlet door and locate and remove one (1) Phillips head screw using your # 2 Phillips screwdriver . Set screw aside. Open up both the cup holder door and the ashtray door. Remove the dash trim bezel that surrounds the radio and climate control and extends across the instrument cluster. To do this, grasp the bezel with your hands on the bottom right side of bezel just above the cup holder door pulling toward you to release a series of clips. Once released, work the re... Read Full Story

Dodge Caliber, Jeep Compass Subwoofer Installation 1. Lift up on the B pillar post cover and then pull it towards the center of the car to remove. 2. Using a panel removal tool gently pry up the threshold/kick panel along the bottom of the front and rear door openings to release fasteners and remove panel. 3. Find the black plastic fastener securing the driver’s side kick panel and unscrew it. 4. Pull backwards on the kick panel to remove it. 5. Pull the cover of the foot rest to snap it loos... Read Full Story